CVE-2026-46148

CVE-2026-46148 is a medium-severity vulnerability in Linux Linux Kernel with a CVSS 3.x base score of 5.5. It is not currently listed as actively exploited by CISA, and its EPSS exploit-prediction score is low.

Key facts

Description

In the Linux kernel, the following vulnerability has been resolved: spi: microchip-core-qspi: control built-in cs manually The coreQSPI IP supports only a single chip select, which is automagically operated by the hardware - set low when the transmit buffer first gets written to and set high when the number of bytes written to the TOTALBYTES field of the FRAMES register have been sent on the bus. Additional devices must use GPIOs for their chip selects. It was reported to me that if there are two devices attached to this QSPI controller that the in-built chip select is set low while linux tries to access the device attached to the GPIO. This went undetected as the boards that connected multiple devices to the SPI controller all exclusively used GPIOs for chip selects, not relying on the built-in chip select at all. It turns out that this was because the built-in chip select, when controlled automagically, is set low when active and high when inactive, thereby ruling out its use for active-high devices or devices that need to transmit with the chip select disabled. Modify the driver so that it controls chip select directly, retaining the behaviour for mem_ops of setting the chip select active for the entire duration of the transfer in the exec_op callback. For regular transfers, implement the set_cs callback for the core to use. As part of this, the existing setup callback, mchp_coreqspi_setup_op(), is removed. Modifying the CLKIDLE field is not safe to do during operation when there are multiple devices, so this code is removed entirely. Setting the MASTER and ENABLE fields is something that can be done once at probe, it doesn't need to be re-run for each device. Instead the new setup callback sets the built-in chip select to its inactive state for active-low devices, as the reset value of the chip select in software controlled mode is low.

Frequently asked questions

What is CVE-2026-46148?
In the Linux kernel, the following vulnerability has been resolved: spi: microchip-core-qspi: control built-in cs manually The coreQSPI IP supports only a single chip select, which is automagically operated by the hardware - set low when the transmit buffer first gets written to and set high when the number of bytes written to the TOTALBYTES field of the FRAMES register have been sent on the bus. Additional devices must use GPIOs for their chip selects. It was reported to me that if there are two devices attached to this QSPI controller that the in-built chip select is set low while linux tries to access the device attached to the GPIO. This went undetected as the boards that connected multiple devices to the SPI controller all exclusively used GPIOs for chip selects, not relying on the built-in chip select at all. It turns out that this was because the built-in chip select, when controlled automagically, is set low when active and high when inactive, thereby ruling out its use for active-high devices or devices that need to transmit with the chip select disabled. Modify the driver so that it controls chip select directly, retaining the behaviour for mem_ops of setting the chip select active for the entire duration of the transfer in the exec_op callback. For regular transfers, implement the set_cs callback for the core to use. As part of this, the existing setup callback, mchp_coreqspi_setup_op(), is removed. Modifying the CLKIDLE field is not safe to do during operation when there are multiple devices, so this code is removed entirely. Setting the MASTER and ENABLE fields is something that can be done once at probe, it doesn't need to be re-run for each device. Instead the new setup callback sets the built-in chip select to its inactive state for active-low devices, as the reset value of the chip select in software controlled mode is low.
How severe is CVE-2026-46148?
CVE-2026-46148 has a CVSS 3.x base score of 5.5, rated medium severity. It is exploitable over local access with low attack complexity, requires low privileges and no user interaction. Impact on confidentiality is none, integrity none, and availability high.
Is CVE-2026-46148 being actively exploited?
It is not currently listed in CISA's KEV catalog. Its EPSS exploit-prediction score is 0% (2nd percentile), an estimate of the probability of exploitation in the next 30 days.
What products are affected by CVE-2026-46148?
CVE-2026-46148 primarily affects Linux Linux Kernel. In total, 3 product configurations (CPEs) are listed as vulnerable; see the affected-products list for the exact versions.
How do I fix CVE-2026-46148?
Review the linked vendor and NVD advisories for patched versions and mitigations, then upgrade or apply the recommended workaround.
Does CVE-2026-46148 have an EU (EUVD) identifier?
Yes. CVE-2026-46148 is tracked in the ENISA EU Vulnerability Database (EUVD) as EUVD-2026-32775.
When was CVE-2026-46148 published?
CVE-2026-46148 was published on 2026-05-28 and last updated on 2026-06-17.

References

Affected products (3)

More vulnerabilities in Linux Linux Kernel

All CVEs affecting Linux Linux Kernel →